Hydraulic Dock Lifts help keep loading operations more efficient, especially where space is restricted. Dock lifts are a cost-efficient alternative to expensive and space-consuming truck well recesses and concrete ramps. Our Dock Lifts can accommodate a wide variety of truck styles; from 20″ step vans or pick-up trucks to high cube vans, standard semi-vehicles and 60” high stake bed vehicles. They can be pit or surface-mounted inside the building or in front of the loading dock. (Surface-mounted dock lifts can be relocated if used in applications where a pit or permanent installation is prohibited.)
Servicing all of Louisiana including New Orleans, Metairie, Slidell, Belle Chasse, and Kenner
- Serco Level Lift Model
- Serco Rail Lift Model
- Serco Load Warrior Air Lift Model
- Serco Load Warrior Turntable Model
- Serco Scissors Dock Lift Model SDL68-5
- Serco Load Warrior Double Scissors Table Model
- Serco Load Warrior Tilter Model
- Serco Load Warrior Scissor Table Model
- Serco Load Warrior Air Tilter
- Kelley HULK Air Lift
Kelley HULK Air Tilter
Design Highlights
- Reinforced, heavy-duty airbag
- Air damper reduces platform bounce
- Fork pockets for simple mobility
Kelley HULK Double Scissors Lift
Design Highlights
- Pre-wired power unit with UL approved control components
- Internally mounted 5 hp power unit
- Self-lubricating composite bearings
- Solid steel legs with stiffener bars
- Turned, ground, polished and hard-chromed axle pins
- Double-wire braided hydraulic hoses
- Velocity fuses on all cylinders to prevent uncontrolled descent
- Polyethylene reservoir allows easy visual check of oil level
- Maintenance locks built into base frame
- Meets or exceeds ANSI MH29.1 standard for industrial scissor lifts
Kelley HULK Hydraulic Dock Lift
Design Highlights
- Beveled toe guards
- 18″ standard solid or split bridge plate
- Dual hydraulic lifting cylinders for optimum performance
- Velocity fuses on lift cylinders prevent uncontrolled descent
- Removable, mandrel-formed tubing handrails
- Maintenance safety strut
- Safety tread steel deck
- Safety chains across operating ends
- Upper travel limit switch
- Available in 4,000 – 20,000 lb. capacities
Kelley HULK Kombo Dock
Benefits
High-performance dock leveler — it provides the same performance benefits of a hydraulic dock leveler such as regenerative hydraulics, powered lip control, safety velocity fuse and push-button controls.
Below-dock operation — In scissor mode, it eliminates the steep grade differences between the vehicle bed and the leveler deck, providing safe, level, below-dock operations.
Scissors lift versatility — Unlike standard scissor lifts, the hydraulically powered dock lip ensures faster cycling times and its
Design Highlights
- 50,000 lbs. Capacity Leveler (per ANSI MH14.1-1987)
- 12,000 lbs. Capacity Lift (8 ft. long units)
- 20,000 lbs. Capacity Lift (10 & 12 ft. long units)
- 18″ Lip Standard
- LED Light Communication Package
- Remote 7.5 HP Independent Lift Motor & Hydraulic System
- PLC Operation
- 1 HP Independent Leveler Motor & Hydraulic System
- Full Feature NEMA 12 Control Panel with Mushroom Style Stop Button
- Remote NEMA 4X Pendant Push Button Hand Control
- Interior Warning Light & Audible Alarm Indicate Dock Lift Is Not In Stored Position
- Safety Velocity Fuse on Leveler and Lift
- Guard Rail Package
- Rear Hinge Blocks
- Protective Roller Curtain on Front
- Side and Rear Weatherseal
- Grease Fittings
Kelley HULK Rail Lift
Design Highlights
- Self-contained power unit/control panel
- Low-profile platform
- Checker plate or smooth deck surface
- 42″ high fixed handrail (optional on 2,500 lb. capacities)
- 18″ long hinged bridge lip (optional on 2,500 lb. capacities)
- Sealed guide bearing rollers
- 60″ high fixed mast guard
- Direct-thrust cylinders provide constant speed through full range of travel
- Velocity fuses on lift cylinders prevent uncontrolled descent
- Self-locking safety/maintenance pin
- Available in 2,500 – 20,000 lb. capacities
Kelley HULK Scissors Lift Table
By bringing the work to the worker, our lift tables not only increase a factory’s productivity, they reduce worker fatigue and drastically decrease the risk of serious back injuries to workers.
Design Highlights
- Solid steel legs with stiffener bars for extra strength and support
- Polyethylene tank prevents condensation, provides easy check of oil level
- High-pressure cylinders with safety velocity fuses to prevent uncontrolled descent
- Pre-wired NEMA-rated controls
- High-strength roller pins with snap rings
- Hardened steel rollers
- High-strength steel polished axle pins
- UL-approved control components
- Meets or exceeds ANSI MH29.1 standard for industrial scissor lifts
Kelley HULK Tilter
Design Highlights
- Pre-wired power unit with UL approved control components
- Power unit internally mounted
- Available in 1 1/2 hp three-phase or 3/4 hp single-phase with 24V AC control valve
- Self-lubricating composite bearings
- Velocity fuses on all cylinders to prevent uncontrolled descent
- Double wire braided hydraulic hoses
- Polyethylene reservoir allows easy visual check of oil level
- Maintenance locks built into frame
- Standard 12′ high lip
- 28″ W x 38″ L minimum platform size
- Meets or exceeds the ANSI MH29.2 standard for industrial tilters
Kelley HULK Truck Leveler
Our Truck Levelers safely raise or lower the vehicle to match the height of the loading dock. This allows for safer loading operations, especially in wet, icy or inclement weather conditions.
Design Highlights
- Surface or pit-mounted units available
- Lift cylinder enclosure
- Push-button activation
- Approach ramp assembly (surface mount only)
- 24″ vertical operating range
- Synchronized lift cylinders with velocity fuses
- High-pressure hoses
- Beveled toe guards
- Internal/external light control package
- Wheel restraint system
Kelley HULK Turntable
Manual or powered models are available to efficiently palletize, build-up and break-down, and either can be mounted on a scissors lift, stable bench, or other surface. In addition, ground-mounting is also available.
Design Higlights
- Rigid base frame with predrilled mounting holes
- 1/2″ thick steel platform with rounded corners
- Tough TGP hard-chromed kingpin
- Rollers are sealed ball bearings for ease of operation
- Roller-pin bushings are self-lubricating
- 34″ x 34″ is minimum turntable size
Kelley HULK Zero Lift
Design Highlights
- 1 HP Power Unit – 115v/1ph/60hz with 115 Volt
- Controls x 10′ of Hose
- Power Unit with UL Approved Electrical Panel
- Push Button Control – NEMA 4X with 10′ of Cable
- Self Lubricating Bushings with Hardened Chrome Pins for Pivot Points
- Velocity Fuses on Cylinders to Prevent Uncontrolled Descent Up Travel Limit Switch
- Maintenance Blocks
